- #Nefmoto how to immo off a bin file drivers
- #Nefmoto how to immo off a bin file software
- #Nefmoto how to immo off a bin file free
You have the bin file saved and want to know what to do with it? In ME 7.5, and ME 7.1.1 ECUs with the Bosch LSU4 lambda sensor the bin file is 1024k. In ME7.1 ECUs without 5 wire lambda sensors the bin file is 512k The above will allow you to pull the bin file.
#Nefmoto how to immo off a bin file software
Software to read the 200-800BB flash chip. I can be general though regarding what is involved. I would like to give more information on this but wish not to upset those who make a living from remapping vehicles. ME7 E-Gas reading, writing and editing general overview I have a lot to learn but i am willing enough and i hope i can share along the way
I will investigate further and post as the saga goes on It could be due to the IMMO off, i dont know I ran it through this program and was expecting it to come back ok, but it found 1 errorĪt this stage i am not sure what this error is and how to fix it MEcheck looks at your flash for incorrect checksums If you dont know how to use CMD there are plenty of guides on the internet I have read i need to check the file to make sure it is ok so i downloaded a program called ME7Check, this program can only be used in a CMD prompt
more info needed to clarify exactly what the ecu size means IE: 512 vs 1024kb bin file and weighs in at 3.1 mb, i'm not sure how a 3.1mb read translates from a 1024kb ecu.
Once i had a succesful Flash read i saved it to my desktop, it is saved as a. I googled and found my ECU was the larger type so i used 29F800BB With the software loaded i plugged in and followed the Nefmoto guide, at this point i had to find what type of memory format my ECU is, from what i gather there are two main types of memory format one is 512kb and the other is 1024kb I fitted my car with an OBD port from a mk6 golf so i'm good to go
#Nefmoto how to immo off a bin file drivers
So i have the software and the cable drivers are installed, its time to go to the car and see what i can do
#Nefmoto how to immo off a bin file free
I settled with the software developed by Tony from Nefmoto as its free and there is lots of information on the site on using itįor the hardware i used a cheap ebay cable from this link įor a great guide on the first steps of using the Nefmoto software read this guide There are a few different programs around to let you read your ECU Flash, not to be confused with reading your Fault codes or DTC's (diagnostic trouble codes) So you need Software and Hardware to read your ECU This website is a VERY indepth place for technical information when attempting to remap your car, beware though don't sign up and expect to be led into remapping by them, they really know their stuff and you need to prove you are understanding the process of what you are trying to do I started by googling for the info i needed on how to remap and eventually came upon The ECU part number is as follows 8N0906018AQ its ME7.5, the Car runs a wideband Lambda and DBW My ECU has had the IMMO off, this was kindly done by Toyotec My Car is a Mk2 8v with an Audi TT Ary fitted and a few small mods, Forward mounted intercooler, and home brew Turbo inlet pipeĪlso it should have a Ko3s Turbo but someone has fitted a K03 at some point so this will limit power I am reasonably computer literate and have in the past flashed and modified the memory of xbox360's to Jtag them so i know enough to get by but i am by no means a computer wiz or a genius ! I'm 43 and have been a mechanic since leaving school, i trained on points and condensors and have never really needed to know about computers on cars until the last few years Lets start with a quick rundown on myself and my car Yes i could pay a company to remap my car and even ask Toyotec to have a go. I have decided to try and remap my 1.8t and thought it would be a good idea to show my progress as i go along so i can record what i have done and also maybe help other understand what needs to be done